Welcome to the LOOP Antenna Community!                                                                  Join and enjoy it!

We've been thinking of a community where we can all exchange ideas, opinions, or simply have a friendly chat about LOOP Antenna.

We rely on all members to help keep these discussion forums a safe place for people to share and view information.

So, please treat other community members the way you would like to be treated: be courteous and respectful, stay on topic, share your knowledge.

We will remove any post that includes personal attacks, swearing or offensive language, non-constructive criticism or falsehoods. Such a poor behavior will result in losing the community posting privileges.                                                                                                                                                                                         Thank you for your time and your help!

Martin Harrison
19 apr 2018

ATU 2 problem

3 commenti

My ATU 2 switched on when putting in power lead, On/Off button does not work, screen stuck showing (flashing):

BOARD: 1.03.0343

INITIALISE USB

It is new (or so the radio shop who sold it told me).

It does not recognise usb pad or keyboard, can not do firmware update because it does not recognise the usb port.

Is there a way to get it working or do I send it back and get a replacement?

Any help, suggestions appreciated.

 

 

Martin Harrison
20 apr 2018

Problem solved, the PSU had a fault, New PSU installed and all works as it should.

Jeff Wallach
3 mag 2018

Just received the Ciro BABY loop antenna. I have the ATU Version 2 (firmware 3.20) with the RS-232 module installed. I plan to use it with an ICOM IC-7300 and a CT-17 line level converter.

Question: Is the RS-485 connector used at all?

 

Thanks!

N5ITU

Martin Harrison
3 mag 2018

I was told the RS-485 connector is used instead of the RS-232 when there is a very long distance between the ATU and Loop (100s of metres).

I post più recenti
  • gm7eey
    6 giorni fa

    Anyone suffer from poor tune on 20m when the Midi loop gets wet? When I build this one I noticed that the Gamma match tubing had a badly seated cap, when I removed it to inspect a few drops of water came out of the tube. Am going to take the loop down today and inspect this again as its been quite wet recently but am interested to know if this is a known issue. This is a used loop and as far as I know it was stored indoors prior to my assembly and when I did the build, the loop was only outdoors for about 2 days before it went on the mast. Was rather surprised to see the water and trying to tun last night when raining, 20m was nothing below 2.1, today now its dry kinda back to normal at 1.6 ish. Real concerned that water is getting into the co-ax section and thats bound to be bad news. 73s Pete
  • Robert Carswell
    ott 23

    Hi I have a brand new Baby Loop and have a problem straight away. After assembly I went through the installation First Turn On process. Set the loop type and moved to using the star key and setting the frequency as advised to 7050 pressing the enter key looks as though it will do something but the ATU just shuts down and restarts. I have attempted the Auto Detect routine and it fails with same issue the ATU just shuts down and restarts. The display shows 18000 khz with a SWR of 1.6 which is presumably after the factory tested the loop. The firmware is 3.29 and the board is 1.06.0663. I have downloaded the firmware again as per the manual and it doesn't appear to do any upgrading as presumably it already knows the firmware installed on the ATU is version 3.29 I have checked the twin core cable I am using with a 12volt battery and it checks out with the volt meter. I have checked the antenna cable which is mini 8 and that checks out. I have attempted the procedure for manual testing of the motor control as per the manual on page 70 entering the frequency of 7050 pressing enter which shows TEST: Duty 21% 7050khz SWR: 9.9 Pressing 9 to open the loop just shuts down and restarts the ATU During the manual testing I have checked across the motor cable plug on the rear of the ATU and there is no voltage at the terminals during any of the setup procedures or the manual testing of the motor control. This is a brand new never used before Baby Loop and fails at the first turn on stage. I have contacted the supplier but being the weekend there is no one available to help Any one any idea of the issue?
  • jeffsmithchicago
    set 19

    I received the Baby loop last week and assembled it. After setting it up a few feet away from the desk I decided to connect it and run some tests to give it a shake down. It worked perfectly considering it was only a few feet away from my radio desk and then it just seemed to die with no error messages or anything. The loop is "open" all the way and will not move at all. When manually entering a frequency it goes thru the normal message of tuning but does nothing else, no motor sound or anything. Any advice to get me going in the right direction?

Ciro Mazzoni Radiocomunicazioni

 

via Bonincontro, 18

37139 Verona -ITALIA-

info@ciromazzoni.com

Tel: +39 0458903104 Fax: +39 0458902633

 

P.IVA 03063020238

© 2014 created by Sergio Mazzoni